|
SYS-1025TC-3FB |
- SuperServer 1025TC-3FB (Black)
|
|
|
Super X7DCT-3F + Super X7DCT-3F |
|
|
CPU |
- Dual 771-pin LGA Sockets
- Supports up to Dual Intel® 64-bit Xeon®processor(s) of the same type below:
- Quad-Core Intel®
Xeon®Processor 5400/5300 sequence (Harpertown /Clovertown processor) up to 3.16 GHz
- Dual-Core Intel®
Xeon®Processor 5200/5100 sequence (Wolfdale/Woodcrest processor) up to 3.40 GHz
|
System Bus |
- 1333 / 1066 MHz system bus
|
Operating System Software |
- Supports 64-bit Operating Systems
- Supports 32-bit Operating Systems
|
|
|
Memory Capacity |
- Six 240-pin DIMM sockets
- Supports up to 48 GB 667/533MHz DDR2 ECC Register DIMM memory
- Dual channels memory bus
|
Memory Type |
- 677/533MHzECC Register DDR2 SDRAM 72-bit, 240-pin gold-plated DIMMs
|
DIMM Sizes |
|
Memory Voltage |
|
Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
|
|
|
Chipset |
- Intel® 5100 (San Clemente) chipset
- Intel® ICH9R SB
|
SAS |
- LSI SAS1064E
- RAID 0, 1, 10 support
- (Optional: AOC-IButton68) RAID 5 support
|
SATA |
- Intel ICH9R SB SATAII Controller
- RAID 0, 1, 5, 10 support (Windows)
- RAID 0, 1, 10 support (Linux)
|
IPMI |
- Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Winbond® WPCM450 BMC
|
Network Controllers |
- Intel® 82575 Dual-Port Gigabit Ethernet Controllers
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- 1x Realtek RTL8201N PHY (dedicated IPMI)
- Intel® I/OAT support for fast, scaleable, and reliable networking
|
Graphics |
|
Super I/O |
|
Clock Generator |
|
|
|
SAS |
|
Serial ATA |
- Four Serial ATA ports
- Four SATA hard drives supported
|
LAN |
- 2x RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
|
USB |
- 2 rear + 1 Type A connector + 2 headers (2 Ports)
- 5 total USB ports, 2.0 Compliant / 1.1 Compliant
|
VGA |
|
Serial Port |
- 1 Fast UART 16550 serial port
|
|
|
BIOS Type |
- 16Mb SPI Flash with Phoenix ® BIOS
|
BIOS Features |
- Plug and Play (PnP)
- DMI 2.3
- PCI 2.2
- ACPI 1.0/2.0/3.0
- USB Keyboard support
- Hardware BIOS Virus protection
|
|
|
|
|
Form Factor |
|
Model |
|
|
|
Height |
|
Width |
|
Depth |
|
Gross Weight |
|
Available Colors |
|
|
|
Buttons |
- Power On/Off button
- System Reset button
|
LEDs |
- Power LED
- Hard drive activity LED
- 2x Network activity LEDs
- System Overheat LED
|
|
|
PCI-Express |
- 1 (x8) PCI-e (in x16 slot - Low Profile)
|
|
|
Hot-swap |
- 4x 2.5" SAS Hot-swap drive bays
|
|
|
1U SATA Backplane |
|
|
Fans |
|
|
|
780W AC to DC power supply w/ PFC |
AC Input |
- 100-240V, 60-50Hz, 9.5-3.5Amp
|
+5V sb |
|
+12V |
- 65 Amp @ 180-240Vac
- 58 Amp @ 100-140Vac
|
|
|
Software |
- Optional IPMI (Intelligent Platform Management Interface) v1.5 / 2.0
- Super Doctor III
- Watch Dog
- NMI
|
Power Configurations |
- ACPI Power Management
- Main Switch Override Mechansim
- Power-on mode for AC power recovery
|
|
|
CPU |
- Monitors for CPU Cores,+1.5V, +3.3V, +5V, ±12V, +5 Stdby, VBAT
- CPU Core 5-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
|
FAN |
- Total of three 4-pin fans
- 3x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
|
Temperature |
- Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x Fan Connectors
- PSU I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
|
LED |
- CPU / System Overheat LED
- Suspend-state Indicator LED
|
Other Features |
|
|
|
RoHS |
- RoHS Compliant 5/6, Server Exemption
|
Environmental Specifications |
- Operating Temperature:
10°C to 35°C (50°F to 95°F)
- Non-operating Temperature:
-40°C to 70°C (-40°F to 158°F)
- Operating Relative Humidity:
8% to 90% (non-condensing)
- Non-operating Relative Humidity:
5% to 95% (non-condensing)
|
|