 |
| SYS-7045A-C3B |
- SuperServer 7045A-C3B (Black)
|
| |
|
| CPU |
- Dual 771-pin LGA Sockets
- Supports up to Dual Intel® 64-bit Xeon®processor(s) of the same type below:
- Quad-Core Intel®
Xeon®Processor
5400/5300 sequence (Harpertown
/Clovertown processor)
up to 3.16 GHz
- Dual-Core Intel®
Xeon®Processor
5200/5100 sequence (Wolfdale/Woodcrest processor) up to 3.40 GHz
|
| System Bus |
- 1333 / 1066 MHz system bus
|
| Operating System Software |
- Supports 64-bit Operating Systems
- Supports 32-bit Operating Systems
|
| |
|
| Memory Capacity |
- Six 240-pin DIMM sockets
- Supports up to 48GB 667/533MHz DDR2 ECC Register memory
- Memory must be populated in pairs
|
| Memory Type |
- 667/533MHz Register DDR2 ECC SDRAM 72-bit, 240-pin gold-plated DIMMs
|
| DIMM Sizes |
- 512MB, 1GB, 2GB, 4GB, 8GB**
|
| Memory Voltage |
|
| Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
|
| |
|
| Chipset |
- Intel® 5100 (San Clemente) chipset
- Intel® ICH9R + PXH-V
|
| SAS |
- LSI SAS1068E
- RAID 0, 1, 10 support
- (Optional: AOC-IButton68) RAID 5 support
|
| SATA |
- Intel ICH9R SB SATAII Controller
- RAID 0, 1, 5, 10 support (Windows only)
- RAID 0, 1, 10 support (Linux)
|
| IPMI |
- Support for Intelligent Platform Management Interface v.2.0
- 200-pin IPMI slot (SIMLP)
- (Optional: AOC-SIMLP-B)
- (Optional: AOC-SIMLP-3) with 3rd LAN support
- NOTE: KVM-over-LAN not supported - there is no DVO signal to the IPMI slot
|
| Network Controllers |
- Intel® Dual 82573V/L Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT support for fast, scaleable, and reliable networking
|
| Audio |
- High Definition 7.1 Channel Audio
|
| Super I/O |
|
| Clock Generator |
|
| |
|
| PCI-Express |
- 1 (x16) PCI-e slot
- 1 (x4) PCI-e (using x16) slot
|
| PCI-X |
- 2x 64-bit 133/100MHz PCI-X (3.3V) slots
|
| PCI |
- 2x 32-bit 33MHz PCI (5V) slots
|
| |
|
| SAS |
|
| Serial ATA |
- Six Serial ATA ports
- Six SATA hard drives supported
|
| IDE |
- Single EIDE channel supports up to two UDMA IDE devices(IDE-M, IDE-S) including CF card
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
|
| Floppy |
- 1 Floppy controller; 1.44 MB
|
| LAN |
|
| USB |
- 4x USB rear ports
- 6x USB internal header
- 10 total USB ports, 2.0 Compliant
|
| Audio |
- High Definition 7.1 Channel Audio
- Line-in / Line-out / Microphone Ports
|
| Keyboard / Mouse |
- PS/2 keyboard and mouse ports
|
| Serial Port / Header |
- 1 Fast UART 16550 serial port
- 1 Header
|
| Parallel Port |
- 1x ECP / EEP Parallel Port
|
|
 |
|
|
| Form Factor |
- 4U Rackmountable / Tower
- Optional Rackmount Kit (CSE-PT26)
|
| Model |
|
| |
|
| Height |
|
| Width |
|
| Depth |
|
| Gross Weight |
|
| Available Colors |
|
| |
|
| Buttons |
- Power On/Off button
- System Reset button
|
| LEDs |
- Power LED
- Hard drive activity LED
- 2x Network activity LEDs
- System Overheat / Fan Fail LED
|
| Ports |
|
| |
|
| Hot-swap |
|
| Peripheral Bay(s) [90o Rotatable] |
- 2x 5.25" Peripheral Drive Bay
- 1x 5.25" Bay For Floppy Drive
|
| |
|
| Floppy |
- Panasonic 3.5" 1.44MB Floppy Drive
|
| |
|
| SC743 SAS / SATA Backplane w/ Enclosure Management |
| |
|
| Fans |
- 2x 8cm Hot-swappable PWM Cooling Fans
- 1x 9cm Hot-Swappable Rear Exhaust PWM Fan
- 2x Active heatsink w/ heatpipe
|
| |
|
| 865W AC power supply (cooling-redundant) w/ PFC |
| AC Voltage |
- 100 - 240V, 50-60Hz, 12-6 Amp
|
| +5V standby |
|
| +12V |
|
| +5V |
|
| +3.3V |
|
| -12V |
|
| Certification |
 80 PLUS Certified |
| |
|
| CPU |
- Monitors for CPU Cores,+1.8V, +3.3V, +5V, ±12V, +3.3V Stdby, +5 Stdby, VBAT, HT, Memory, Chipset
- CPU Core 6-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
|
| FAN |
- Eight 4-pin fans
- 8x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Support for 3-pins
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connectors
|
| Temperature |
- Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x Fan Connectors
- PSU I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
|
| LED |
- CPU / System Overheat LED
- Suspend-state Indicator LED
- +5V Standby alert LED
|
| Other Features |
- Chassis Intrusion Detection
- Chassis Intrusion Header
- SDDC Support
|
| |
RoHS
|
|
| Environmental Spec. |
- Operating Temperature: 10° to 35°C (50° to 95°F)
- Non-operating Temperature: -40° to 70°C (-40° to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
|
|
Купить / Заказать / Узнать цену
