|
SYS-6016TT-IBXF |
- SuperServer 6016TT-IBXF (Black)
|
|
|
Super X8DTT-IBXF + Super X8DTT-IBXF |
|
|
CPU |
- Dual 1366-pin LGA Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
- Intel® Xeon® Processor X5600/E5600/L5600 Series
(Westmere) 40W - 130W
- Intel® Xeon® Processor X5500/E5500/L5500 Series
(Nehalem-EP) 38W - 95W
|
QPI |
|
|
|
Memory Capacity |
- 12x 240-pin DIMM sockets
- Supports up to 192 GB** 1333 / 1066 / 800MHz DDR3 ECC Registered memory
- Supports up to 48 GB 1333 / 1066 / 800MHz DDR3 ECC / Non ECC Unbuffered memory
- Memory Mirroring supported
|
Memory Type |
- 1333 / 1066 / 800MHz ECC Registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
|
DIMM Sizes |
- 1GB, 2GB, 4GB , 8GB** , 16GB**
|
Memory Voltage |
|
Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
|
|
|
Infiniband |
- Mellanox ConnectX-2 DDR Infiniband 20Gbps Controller
|
Chipset |
- Intel® 5520 (Tylersburg) chipset
- ICH10R + IOH-36D
|
SATA |
- Intel ICH10R SATA 3.0Gbps Controller
- RAID 0, 1 support
|
IPMI |
- Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Winbond® WPCM450 BMC
|
Network Controllers |
- Intel® 82576 Dual-Port Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT 3 support for fast, scaleable, and reliable networking
- VMDq support for better performance of virtualization
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
Graphics |
|
Super I/O |
|
Clock Generator |
|
|
|
Serial ATA |
- Six Serial ATA ports
- Six SATA hard drives supported
|
LAN |
- 2x RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
|
USB |
- 2 rear + 1 header (2 Ports)
- 4 total USB ports, 2.0 Compliant / 1.1 Compliant
|
VGA |
|
Serial Port |
- 1 Fast UART 16550 serial port
|
Infiniband |
- 1 External QSFP Infiniband Connector
|
|
|
BIOS Type |
- 32Mb SPI Flash EEPROM with AMI® BIOS
|
BIOS Features |
- Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
|
|
|
|
|
Form Factor |
|
Model |
|
|
|
Height |
|
Width |
|
Depth |
|
Gross Weight |
|
Available Colors |
|
|
|
Buttons |
- Power On/Off button
- System Reset button
|
LEDs |
- Power LED
- Hard drive activity LED
- 2x Network activity LEDs
- System Overheat LED
|
|
|
PCI-Express |
- 1 (x16) PCI-E ( Low Profile)
|
|
|
Hot-swap |
- 2x 3.5" SATA Hot-swap drive bays
|
|
|
1U SATA Backplane |
|
|
Fans |
|
|
|
1200W high-efficiency power supply with PMBus |
AC Input |
- 100 - 140V, 50 - 60Hz, 7.5 - 11Amp
- 180 - 240V, 50 - 60Hz, 5 - 8Amp
|
DC Output +5V standby |
|
DC Output +12V |
- 74 Amp @ 100-140V
- 100 Amp @ 180-240V
|
Certification |
80 PLUS Gold Certified [ Test Report ] |
|
|
Software |
- IPMI (Intelligent Platform Management Interface) v1.5 / 2.0 with KVM support
- Super Doctor III
- Watch Dog
- NMI
|
Power Configurations |
- ACPI Power Management
- Main Switch Override Mechansim
- Power-on mode for AC power recovery
|
|
|
CPU |
- Monitors for CPU Cores,+1.5V, +3.3V, +5V, +12V, +5 Stdby, +3.3 Stdby, VBAT, Memory Voltages.
- CPU Core 6-Phase-switching voltage regulator
|
FAN |
- Total of four 4-pin PWM fans
- 4x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
|
Temperature |
- Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 4x Fan Connectors
- PSU I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
|
LED |
- Power Fail / Overheat LED
- Suspend-state Indicator LED
- UID LED
|
Other Features |
|
|
|
RoHS
|
|
Environmental Spec. |
- Operating Temperature: 10° to 35° C (50° to 95°F)
- Non-operating Temperature: -40° to 70° C (-40° to 158° F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
|
|